The EVO MFG 2.5" JL Enforcer Lift Suspension Systems
lift your 2018+ Jeep Wrangler JL 2.5"s. Our main goal in developing this
kit was to give a smooth ride on and off road while giving additional lift with
increased performance. The JL Enforcer kits are specifically designed to
lift your JL and maintain compliant spring rate, smooth ride quality with the use
of your choice of aftermarket 2/2.5" lift shocks. These kits come with a
set of 2.5" Plush Ride Lift springs specific to each corner which will
keep the Jeep Wrangler JL Level side to side and will maintain a unique and
compliant ride quality. EVO MFG JL Enforcer kits are available in multiple
configurations to suit your needs and budget and are upgradable down the road.
These Enforcer kits will fit up to a 37" tires on Rubicon Model JLs or
35" tires on Sahara and Sport/S.
The EVO MFG 2.5" JL Enforcer Kits are easy to install
using normal tools. No drilling or cutting (optional rear shock extensions
require one minor drill). They require no driveshaft or exhaust modifications
(your shock choice may require this, contact manufacturer to be sure). Simple
Bolt on installation.
2.5" lift is based on increase of a 4 Door
Rubicon. 4 Door Sport and Sahara Models will see slightly higher
increases over stock and will match overall lift height of a Rubicon
Model. 2 Door Models (all) will see slightly higher increases in lift.
Increases will vary across all models and equipment.
Stage 1 kits includes all minimum necessary parts to lift your JL
Stage 2 kits includes Stage 1 components as well as EVO MFG Enforcer JL Front
Lower Adjustable Control Arms to allow for caster adjustments.
Stage 3 Kits includes stage 2 components as well as EVO MFG Enforcer rear
upper adjustable control arms for rear pinion angle adjustment
Stage 4 kits includes stages 1 components with all 8 EVO MFG Enforcer control
arms for full front and rear axle adjustments.
The difference with EVO MFG Enforcer Overland systems vs
EVO MFG Enforcer systems is the use of front Overland Control Arm
Brackets. When lifting your vehicle your control arms at ride height
have a steeper angle towards the floor which can have some negative
effect/chop in ride quality. With the use of the
included Overland Control Arm brackets we relocate the front control arm
mounting locations at the frame. In doing this when lifted we
maintain factory flatter control arm angles and while minimal, we
alleviate much of the chop associated with lifting a Jeep giving even
better and more improved ride quality. Also, in the use of
Overland Drop Brackets we are able to engineer more performance into the
front suspension to improve braking and driveline angles through
suspension cycle. Both kits drive very well, the Overland Kits are
better suited for less hard off-road crawling and more light off road and
on road use.
* 2.5" Enforcer Kits have the option of
choosing front and rear shock extensions. These will all retain
factory shocks while maintaining full shock travel.
* "K" kits include a set of EVO SPEC
King 2.5" Remote Reservoir King Shocks
* "K2" Kits include a set of EVO
SPEC King 2.0 Smooth Body Shocks
* "BIL" Kits include a set of
Bilstein 5100 Shocks.
Front aftermarket driveshaft is not required when equipped
with grouped shocks above.
*Front and rear adjustable trackbars are included with PLUS
"P" kits. Recommend but not required on 2.5" kits.
Note: Depending on actual tire variances and
sizes, Some minor factory inner liner plastic may need to trimmed/removed
to fully clear some tires under compression. Factory wheels are
compatible on all EVO MFG JL JL 2.5" Enforcer kits and can be used with
the above advertised 35/37 tires.